RCU2E-A40 Base Kit for Lumens and Minrray

Model: RCU2E-A40™

Part #: RCU2E-A40

Extends camera power (no factory camera PSU required), PTZ control, audio and video over CAT5e/CAT6 cable up to 100m.
Simple Plug and Play installation, no programming required.
Ethernet streaming video supported on 100/1000 capable devices
All hardware-specific camera and codec connection cables included.
PowerSniffer included for testing SCTLink™ cable conductor continuity.

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Related Products

Documents

Expanding on the reliable and time-tested technology of SCT’s RemoteCam™ platforms, the RemoteCamUSB2E™ is part of Sound Control Technologies’ next generation product portfolio for USB PTZ cameras. The RemoteCamUSB2E™ platform offers a cost and time saving alternative when integrating USB PTZ cameras into a wide variety of presentation spaces. The RemoteCamUSB2E™ Kits provide a reliable “transparent“ link between the camera and codec/head-end.

Supported Manufacturers: Lumens VC-TR1, Minrray UV510A.

Base Kit: Inclusive of RCU2E Modules, Kit Cables and Power Supply

RCU2E-CE Camera Interface Module

RCU2E-HE Codec/Head-End Interface Module

PPC-C004-0.4M DC Power Plug (RCU2E-CE™) to EIAJ-4 DC Power Plug

RCC-C002-0.3M RJ45 (RCU2E-CE™) to RJ45

RCC-M003-0.3M USB-A (RCU2E-CE™) to USB-A

RCC-H016-1.0M RJ45 (RCU2E-CE™) to RJ45

RCC-M004-1.0M USB-B (RCU2E-HE™) to USB-A

RCC-M014-1.0M USB-B (RCU2E-HE™) to USB-C

WPS-12 Power Supply.

Extends camera power (no factory camera PSU required), PTZ control, audio and video over CAT5e/CAT6 cable up to 100m.
Simple Plug and Play installation, no programming required.
Ethernet streaming video supported on 100/1000 capable devices
All hardware-specific camera and codec connection cables included.
PowerSniffer included for testing SCTLink™ cable conductor continuity.
Integrator only required to provide CAT5e/CAT6 SCTLink™ Cable.
Field-upgradable firmware via microSD Card.
Video Format: USB Video typically up to 1080p30/720p60
UVC and IP Camera Control
USB Tier Usage: 1 tier (hub) per linked set
Two port 10/100/1000 Ethernet switch (RCU2E-HE™): Dual RJ45 connector
100/1000* Ethernet (RCU2E-CE™): RJ45 connector, Passive PoE, 48VDC up to 24W
Power Out Connector (RCU2E-CE™): 5.5x2.5mm DC jack, 12VDC up to 1.2A
USB Connector (RCU2E-CE™): USB-A for Data and 5V Camera Power up to 1.2A
USB Connector (RCU2E-HE™): USB-B 2.0 for Host Connection
Audio In/Out: 3.5mm TRS Jacks, Stereo Line Level Unbalanced
SCTLINK™ CABLE SPECS:
SCT recommends CAT6 or better cable for the SCTLink™. The use of a shielded cable, while not required for most platforms, is highly recommended.
Proper termination and testing, along with good cable management, minimizes potential problems.
1000 Mbps only supported for SCTLink™ cables up to 15m
Wiring Termination Standard T568A or T568B 100m Maximum Length (No Minimum Length)
RCM™ Series On-Wall Mounts:
Integrate mounting of the camera and the RCU2E-CE™ Camera End Module.
Camera plates are laser cut to match the contour of the camera base.
Cleanest mounting solution available, using an integrator-supplied US standard 2-Gang Box or Low Voltage Ring.
Provides cable concealment and ease of installation.
An RCW™ Series variant is also available for masonry or other solid walls where a 2-Gang Box or Low Voltage Ring cannot be used.
RCR™ Series In-Wall Recessed Mounts:
Integrate mounting of the camera and the RCU2E-CE™ Camera End Module.
Three-piece all-metal solution with a common back box and bezel.
Camera plates are laser cut to match the contour of the camera base.
Camera plate has depth mounting options to meet specific requirements.
Designed to meet ADA compliance in most cases (camera dependent).
RCS™ Series Sheetrock Ceiling Mounts:
Integrate mounting of the camera and the RCU2E-CE™ Camera End Module.
Three-piece all-metal solution with a common Backbox.
Camera specific with a custom cradle or a 1/4 20 bolt to securely hold the base of the camera
RCT™ Series T-Bar Ceiling Mounts:
Integrate mounting of the camera and the RCU2E-CE™ Camera End Module.
Three-piece all-metal solution with a common T-Bar Bracket.
Camera specific with a custom cradle or a 1/4 20 bolt to securely hold the base of the camera.
RC-RKM™ 2RU 12” Deep Rack Shelf:
Designed to mount the RCU2S-HE™, RCU2E-HE™, RC4-HE™, RC5-HE™, RC6-HE™, RC7-HE™, RC8- HE™, RTK-RX™ and RC-SDA™ modules, specific manufacturer codecs, and power supplies.
Leaves access to rear of modules for clean and easy cabling, while providing proper ventilation
RC-RK2™ 1RU 9” Deep Rack Shelf:
Designed to mount two of our RCU2S-HE™, RCU2E-HE™, RC4-HE™, RC5-HE™, and RCSDA™ modules, and two of our WPS-12™ power supplies, while leaving access to rear of modules for clean and easy cabling.
RC-RK4™ 1RU 14” Deep Rack Shelf:
Designed to mount four of our RCU2S-HE™, RCU2E-HE™, RC4-HE™, RC5-HE™, and RCSDA™ modules, and four of our WPS-12™ power supplies, while leaving access to rear of modules for clean and easy cabling.

Warranty - Yes
Spec Sheet available - Yes

Warranty (Length/Type): 3 Years
Certifications: UL, CE, FCC, CCC, TÜV, RCM+GEMS, LPS, BIS, PSE, CB, DoE VI, CoC V5 and RoHS2
Active Power: 4.80 Watt
RCU2E-CE™ Camera End Module:
•Imperial Dims: H: 0.789 x W: 2.264 x D: 3.725 inch
•Metric Dims: H: 20mm x W: 57mm x D: 94mm
•Weight: 0.2 lbs / 90g
RCU2E-HE™ Head End Module:
•Imperial Dims: H: 1.448 x W: 3.814 x D: 3.578 inch
•Metric Dims: H: 36mm x W: 96mm x D: 90mm
•Weight: 0.4 lbs / 181g
WPS-12™ Power Supply (Included) :
•Imperial Dims: H: 1.19 x W: 1.85 x D: 4.65 inch
•Metric Dims: H: 30mm x W: 47mm x D: 118mm
•Weight: 0.5 lbs / 236g
•Input: 100 to 240VAC, 47-63Hz, 1.45A Max
•Output: 30VDC, 2A Max
•Output Connector: 5.5mm x 2.5mm DC Barrel

RCU2E-A00™ - RCU2E-A00 Base Kit for Lumens and Minrray

RCU2E-B00™ - RCU2E-B00 Base Kit for Multiple Manufacturers

RCU2E-B30™ - RCU2E-B30 Base Kit for Multiple Manufacturers

RCU2E-B40™ - RCU2E-B40 Base Kit for Multiple Manufacturers

RCU2E-C00™ - RCU2E-C00 Base Kit for Multiple Manufacturers

RCU2E-C40™ - RCU2E-C40 Base Kit for Sony

RCU2E-C50™ - RCU2E-C50 Base Kit for Panasonic Cameras

Base Kit 575800 kb - Data Sheet

Project List