Network Equipment : Network Hubs & Switches : FOR-A Corp. of America - IPS-6200

Seamless IP Change Over Switcher

Model: IPS-6200

Seamless switching between outputs of the same encoder
When installed at the far end of a network link, the IPS-6200 seamlessly switches between redundant encoder TSoIP input used in multicast transmissions or the like
This supports completely seamless switching without video or audio disruption
Auto and manual switching
When a signal error occurs, the IPS-6200 automatically switches to the other line

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Related Products

Documents

Clean Switching Over IP
Increasing IP circuit reliability

Standalone ASI/TS over IP changeover in a 1U enclosure. Monitors TS-level IP signals in redundant input and instantly switches ports if errors occur, enabling seamless output without disruptions.
IP-based changeover for monitoring redundant TSoIP signals from multicast TS-level encoder transmissions and seamlessly switching ports if errors occur. To prevent transmission path error, this changeover further increases the reliability of duplex transmission.

Seamless switching between outputs of the same encoder
- When installed at the far end of a network link, the IPS-6200 seamlessly switches between redundant encoder TSoIP input used in multicast transmissions or the like
- This supports completely seamless switching without video or audio disruption
Auto and manual switching
- When a signal error occurs, the IPS-6200 automatically switches to the other line
- Manual switching and auto/manual assignment of each line are also possible
- For example, the following assignment can be selected: Automatic switching from the current line to the reserve line, and manual switching from the reserve line to the current line
Delay adjustment function
- The delay difference between different lines is absorbed quickly and both phase inputs are automatically aligned to achieve seamless switching that does not disrupt the output
- The delay adjustment range is up to 10 seconds
TS-level monitoring
- TS-level error monitoring, already proven reliable in switching, is used for IP signals
- Error monitoring goes beyond TR 101 290 guidelines to check for packet loss, null-only, and other critical errors affecting signal quality
- Error detection can also be enabled or disabled based on the type of signal
- Set the PID error detection threshold as desired, in 1 ms increments
- Up to four sets of multi-program signals are supported
GUI-based remote control and monitoring
- Ethernet interfaces enable a wide range of remote monitoring and control to suit many usage scenarios
- The dedicated GUI can be used to make settings and graphically display error monitoring contents via Ethernet
- An event log viewer, automatic CSV file generation, and other functions are also provided to facilitate signal management requiring historical condition data
- SNMP-based control, configuration, and monitoring is also supported
ASI and IP input both supported
- Choose ASI or IP for each signal supplied. Enables mixed input, using IN 1 on the IP side and IN 2 on the ASI side, for example. Ideal for redundant ASI/satellite operation.

Spec Sheet available - Yes

Operating Temperature (Maximum): 104 F
Operating Temperature (Minimum): 41 F
Number of Inputs: 2
Number of Outputs: 1
Rack Units (Height): 1
AC Voltage (Maximum): 240 Volts
AC Voltage (Minimum): 100 Volts
Active Power: 30 Watt
Depth: 17.72 in
Height: 1.73 in
Width: 16.93 in
Product Weight: 15.43 lbs
IP port:
- Transmission standard: IEEE 802.3ab / IEEE 802.3u compliant
- Connector: RJ-45 (Input × 2, Output × 1)
ASI port:
- Signal standard: DVB-ASI (EN50083-9) compliant
- Input: Packet / Burst, 188 / 204 bytes
- Output: Packet, INPUT / 188 byte fixed /204 byte fixed
- Effective bit rate: 1 Mbps to 200 Mbps
- Connector: 75 ohms unbalanced BNC (Input × 2, Output × 2)
- Pass-through: Pass-through from IN 1 to OUT (via mechanical relay) when the power is turned off
TS over IP:
- Transmission standard: SMPTE 2022-2
- Transmission protocol: RTP/UDP/IPv4
- FEC: SMPTE 2022-1 / Pro-MPEG CoP#3
- Communication format: Unicast/multicast (IGMPv2)
- TSP over IP: 1-7
Monitor/control system:
- Buffer capacity for delay adjustment: 10 seconds
- System delay: Standard 50 ms / min. 5 ms (depends on the offset value)
- Error detection item (Can be enabled/disabled for each signal)
  - No signal
  - Packet loss (including illegal code error)
  - TR101 290 P1 / P2 (PMT 1-4 error detection for MPTS can be configured individually.)
  - NULL only error
External control:
- ETHERNET
  - 10BASE-T / 100BASE-TX / 1000BASE-T
  - Signal status monitoring / Main unit setting / Log viewer / File save function by dedicated GUI
  - SNMP monitoring / control by means of dedicated MIB files (SNMP v1 / v2c) (Main unit control and notification of error traps for up to four different IP addresses)
  - For Maintenance (For firmware updates)

TSS-6200 - TS Seamless Switch

Switcher 303 kb - Data Sheet

Project List

Suggested Products

MXNet 10G 24 Port Copper Network Switch

by AVPro Edge

MXNet 10G 24 Port Copper Network Switch

by AVPro Edge

MXNet 10G 12 Port Network Switch

by AVPro Edge